FYT-1改进型防水涂料沥青防水涂料厂家直供,甘肃FYT-1改进型桥面防水涂料包工包料价格,fyt-1道桥防水涂料,FYT-1防水涂料,道桥防水涂料,FYT-1路桥专用防水涂料 fyt-1防水剂 f

点击图片查看原图
?
单价: 1000.00元/
起订: 1
供货总量: 9000000
发货期限: 自买家付款之日起 1 天内发货
所在地: 广东
有效期至: 长期有效
最后更新: 2019-04-18 06:40
浏览次数: 2186
询价
?
公司基本资料信息
详细说明
产品规格: 50kg 产品数量: 90000.00 吨
包装说明: 价格说明: 不限
查看人数: 117 人 本页链接: http://info.b2b168.com/s168-95787699.html
公司编号: 14270862 更新时间: 2019-03-10 01:18:55


爱迪斯(中国)有限公司

产品简介: FYT-1改进型防水涂料,是一种高分子复合材料,属国家重点科技推广项目,经国家权威部门组织的专家鉴定,达到同类产品的优秀水平。产品经交通部公路工程检测中心测试,全部技术指标均符合JT/T575-2005标准要求;符合JTT041-2000(公路桥涵施工技术规范),采用特种国产沥青或进口石油沥青为主要原料,配以各种表面活性剂及多种化学助剂、SBS热塑性橡胶为辅助原料 ,在掺加大剂量的高分子聚合物树脂进行改性,生产的一种新型复合防水涂料。 产品特性: 1、施工工艺简单,施工可用机械喷涂也可人工涂刷,干燥快、工期短。 2、该防水层造价便宜,一般只需涂刷三遍即可达到防水效果。 3、防水层与基层、防水层与上部沥青混凝土粘接牢固。 技术指标: ◆ 主要技术指标(依据JT/T 535-2004和JC/T975-2005《路桥用水性沥青基防水涂料》标准要求) 适用范围: 适用于高速公路桥梁、城市立交桥及桥涵等防水工程。 施工、运输和贮存: 1、施工工具准备:施工前应备好拌料桶、喷涂机械或专用鬃刷。 2、基层要求:桥面板,梁混凝土强度达到设计标号、表面不得有松散浮浆、掉皮、空鼓和严重开裂现象。表面平整度应符合桥梁规范要求,垂直排水管上口的标高应低于基层标高,排水口必须与基层安装牢固,不得有任何松动现象。 3、基层应干净、干燥、无积水。 4、基层处理:基面不得有尘土、浮灰、杂质、油渍等,做防水层前可用空压机、净水、去油剂等将表面处理干净,如有混凝土、砂浆等结硬杂物,应将其打磨掉。 5、防水层施工步骤:(以三涂为例) 1)涂刷前应将桶装涂料搅拌均匀。 2)大面积涂刷前先用小刷对漏口处做两遍涂料,对阴角部位加强涂刷防水涂料三遍,然后大面积刷遍涂料。 3)遍涂料实干后即可涂第二遍料。 4)第二遍涂料表干后涂刷第三遍涂料。 6、涂料用量:0.5-1.0kg/㎡,涂膜厚度一般0.6~1.3.mm,喷涂0.3公斤/㎡。 7、施工温度在0~35摄氏度为宜,雨天、冰冻期不宜施工。 8、包装产品用带盖铁桶包装,每桶重量为200kg、50kg 9、运输:该产品无毒不易燃,可按一般运输方式运输。 10、贮存:产品贮存期为6个月,应贮存在0摄氏度以上的仓库,夏季应避免阳光暴晒。 Product Description: FYT-1 modified waterproof coating is a kind of polymer composite material. It is a national key scientific and technological extension project. It has been appraised by experts organized by state authoritative departments and has reached the leading level of similar products. The product has been tested by the Highway Engineering Testing Center of the Ministry of Communications, and all the technical specifications meet the requirements of JT/T575-2005; JTT041-2000 (Highway Bridge and Culvert Construction Technical Specification), using special domestic asphalt or imported petroleum asphalt as the main raw material, with various surfactants, chemical additives and SBS thermoplastic rubber as auxiliary. A new kind of composite waterproof coating was produced by adding a large amount of polymer resin as auxiliary material. Product characteristics: 1, construction technology is simple, construction can be machine spraying, also can be artificially painted, fast drying, short construction period. 2, the waterproof layer is cheap, generally only three times to achieve the waterproofing effect. 3. The waterproof layer is firmly bonded with the base layer, waterproof layer and the upper asphalt concrete. Technical indicators: _Major technical indicators (according to JT/T 535-2004 and JC/T 975-2005 "water-based asphalt waterproof coating for roads and bridges" standard requirements) Scope of application: It is suitable for waterproofing works of expssway bridges, urban overpasses, bridges and culverts. Construction, transportation and storage: 1, construction tools pparation: before construction, mixing drum, spraying machine or special bristle brush should be ppared. 2. Requirements of base course: The strength of bridge deck and beam concrete reaches the design mark, and there must be no loose floating slurry, peeling, hollowing and serious cracking on the surface. Surface smoothness should meet the requirements of bridge specifications, the elevation of vertical drain pipe should be lower than the base elevation, drain must be firmly installed with the base, there must be no loosening phenomenon. 3, the grass roots should be clean, dry and without water accumulation. 4. base treatment: there must be no dust, floating ash, impurities, oil stains, etc. on the base surface. Before making waterproof layer, air compssor, water purification, degreasing agent can be used to clean the surface. If there are concrete, mortar and other hard debris, it should be ground off. 5, waterproof layer construction steps: (take three TU as an example) 1) the barrel coating should be evenly mixed before painting. 2) Use a small brush to paint the leak twice before large-area brushing, and then brush the waterproof coating three times at the corner of the shade, and then brush the first time in a large area. 3) the first coating can be coated with second times after drying. 4) second times dry paint after coating third times of paint. 6, the dosage of paint is 0.5-1.0kg/, the coating thickness is 0.6~1.3.mm, and the spray is 0.3 kg / h. 7. Construction temperature is suitable for 0~35 degrees Celsius. Rainy days and freezing periods are not suitable for construction. 8, packaging products are covered with iron drum packaging, the weight of each barrel is 200kg, 50kg 9, transportation: the product is non-toxic and non inflammable, and can be transported in general transportation mode. 10. Storage: Product storage period is 6 months, should be stored in warehouses above 0 degrees Celsius, summer should avoid sun exposure.

更多>本企业其它产品
FYT-1改进型防水涂料沥青防水涂料厂家直供,甘肃FYT-1改进型桥面防水涂料包工包料价格,fyt-1道桥防水涂料,FYT-1防水涂料,道桥防水涂料,FYT-1路桥专用防水涂料 fyt-1防水剂 f
0相关评论
Copyright???2017-2019??化工之家??版权所有??合作联系QQ:875001151

工商网监标识

?